RJ45 Keystone Jack, Female to Female Cat6a Shielded
This slim profile keystone insert consists of a Cat6a RJ45 female on one end and a Cat6a RJ45 female on the other end. It is typically used to snap into a standard keystone opening and connect a RJ45 Cat6a male cable coming from within the wall to a RJ45 Cat 6a cable going to a source or device.
RJ45 Male Plug Dust Cap – Black (100 pack)
This dust cap fits RJ45 male plug. It is typically used to help keep contaminants off of RJ45 plugs.
RJ45 Male with IP68 Shroud to Blunt Cat6 Solid UTP Gel Filled Outdoor UV / Direct Burial Pigtail Cable
This Cat6 UTP gel filled outdoor UV direct burial Ethernet cable consists of RJ45 male with IP68 rated shroud on one end and and has no termination on the other. The un-terminated end is typically used for punching down onto a jack or panel and the IP68 shroud is intended to mate with our IP68 rated couplers for a weather tight seal. It is typically used outdoors either above or below ground as premise wiring to connect network devices.
RJ45 to Blunt Cat5e Solid FTP Outdoor UV Direct Burial Pigtail Cable – Black
This Cat5e FTP outdoor UV direct burial ethernet cable consists of a RJ45 male on one end and a RJ45 male on the other. It is typically used outdoors either above or below ground as premise wiring to connect network devices.
RJ45 to Blunt Cat5e Solid UTP Outdoor UV Direct Burial Pigtail Cable – Black
This Cat5e UTP outdoor UV direct burial ethernet cable consists of a RJ45 male on one end and has no termination on the other. The un-terminated end is typically used for punching down onto a jack or panel and the RJ45 end can be used outdoors either above or below ground as premise wiring to connect network devices.
RJ45 to Blunt Cat6 Solid FTP Outdoor UV Direct Burial Pigtail Cable – Black
This Cat6 UTP gel filled outdoor UV direct burial Ethernet cable consists of RJ45 male with IP68 rated shroud on one end and and has no termination on the other. The un-terminated end is typically used for punching down onto a jack or panel and the IP68 shroud is intended to mate with our IP68 rated couplers for a weather tight seal. It is typically used outdoors either above or below ground as premise wiring to connect network devices.
ROUND TYPE W:70 X W1:40 X H:15 X H1:10MM X 2M GREY
Wiring Duct with adhesive tape without mounting hole round type, grey color
W:70 x W1:40 X H:15 X H1:10MM * 2
RT-XLR-FMM-01.5
This splitter cable features an XLR female connector on one end and two XLR male connectors on the other, allowing for the duplication of a microphone or XLR output into two balanced channels. It uses high-flex balanced 24AWG cables that ensure optimal audio performance by capturing all highs and lows. The cable’s braided shield provides maximum EMI/RFI noise rejection, maintaining a clean signal. Its multi-stranded copper conductors and ultra-flexible, durable jacket enhance mobility. The FT4 riser fire-rated jacket allows for in-wall use, and the lead-free, silver-laced solder ensures reduced loss and maximum conductivity.
Screw, 1/4-20, 1.25 inch Length, Pan-Head, Quadrex Zinc (25 pack)
These screws have a 1/4-20 thread and are 1.25 inches in length. They are compatible with our CC-BC0250 beam clamp and CC-HN01-075-25 nuts and are typically used to secure our loop cable hangers to our beam clamps in a perpendicular fashion. They are zinc plated and are sold in packs of 25.
*Nuts Sold Separately
Screw, 1/4-20, 3/4 inch Length, Pan-Head, Quadrex Zinc (25 pack)
These screws have a 1/4-20 thread and are 3/4 inches in length. They are compatible with our CC-BC0250 beam clamp and CC-HN01-075-25 nuts and are typically used to secure our loop cable hangers to our beam clamps in a parallel fashion. They are zinc plated and are sold in packs of 25.
*Nuts Sold Separately
Sealed Lead Acid Battery 12V 12amp
The BT-12V-12AF2 is a 12 volt, 12 amp sealed lead acid, non-spillable, rechargeable battery. This battery is typically used as a replacement battery in UPS systems, security alarm systems or security lighting applications.
Sealed Lead Acid Battery 12V 18amp
The BT-12V-18A is a 12 volt, 18 amp sealed lead acid, non-spillable, rechargeable batteries. This battery is typically used as a replacement battery in UPS systems, security alarm systems or security lighting applications
Sealed Lead Acid Battery 12V 26amp
The BT-12V-26A is a 12 volt, 26 amp sealed lead acid, non-spillable, rechargeable battery. This battery is typically used as a replacement battery in UPS systems, security alarm systems or security lighting applications.
Sealed Lead Acid Battery 12V 3amp
The BT-12V-3A-B is a 12 volt, 3 amp sealed lead acid, non-spillable, rechargeable battery. This battery is typically used as a replacement battery in UPS systems, security alarm systems or security lighting applications. Note that the positive terminal is located on the left side of the battery.
Sealed Lead Acid Battery 12V 5amp
The BT-12V-5AF2 is a 12 volt, 5 amp sealed lead acid, non-spillable, rechargeable battery. This battery is typically used as a replacement battery in UPS systems, security alarm systems or security lighting applications.
Sealed Lead Acid Battery 12V 7.5amp
The Sealed Lead Acid Battery 12V 7.5amp, also known as the SLA 12V 7.5Ah battery, is a dependable and efficient power source designed to meet the specific energy needs of various applications. This non-spillable, rechargeable battery is engineered for longevity and reliability.
Sealed Lead Acid Battery 12V 9amp
The BT-12V-9AF2 is a 12 volt, 9 amp sealed lead acid, non-spill able, rechargeable battery. This battery is typically used as a replacement battery in UPS systems, security alarm systems or security lighting applications.
Single Gang Coax Wall Plate – White
This wall plate kit consists of a wall plate, and a F-type coaxial female to female insert. It is designed to snap on to mounting plate. It is compatible with standard North American electrical openings, data clips or surface mount boxes.
